DEALERS
SEARCH
MENU
Products Menu
Share:
Accessories

The new Audison DRC MP (Digital Remote Control Multimedia Play) is compatible with all the Audison electronics featuring AC Link bus. Its slim profile along with the holder supplied with it eases the installation in the best position inside the car. Thanks to the new Joystick, “Rubber Touch” finished for best control of the movements along the four direction axes, the “DRC Settings” menu can be adjusted and navigation is also possible through the “Navi Command” function if the system features an Audison bit Play HD with video output connected to a monitor.

Read More

DRC AB enables the main system control (volume, balance, fader and subwoofer volume, bass-boost) without the use of a PC. Thanks to this device, installed in an ergonomic position within the car dashboard, the user can: choose between the four DSP presets and select the source among master, auxiliary and the two optical digital inputs.

Read More

Stereo passive mixer (unpowered) featuring 4 input channels and 2 output channels, designed for active OEM multi-way systems where each speaker is powered by one specific amplified channel. SPM4 mixes audio through 4 audio transformers specifically developed to achieve very low distortion and highly linear acoustic response. SPM4 provides the ability to mix the midrange/woofer and tweeter channels coming from the amplifier and supply one single mid-high channel. The Ch1(L/R) channels feature two inputs, one features an inverting input compared to Ch2 (L/R) channels; the mixing process often gives better results when one of the two channels undergoes a 180° dephasing. SPM4 is especially recommended to extend the number of inputs of the Audison digital processors or amplifiers with built-in DSP because they feature a De-equalizer (De-Eq). In that case, any possible non-linear acoustic emissions due to the mixing of the pre-existing filtered channels are duly compensated.

Read More

It prevents the processor from shutting down when turning on vehicles featuring the start & stop system

When starting the engine, the vehicle battery voltage might decrease below 8 Volts value. If a signal processor (bit One, bit Ten) is installed in your system, especially with vehicles featuring the start & stop system, low supply voltage values might make the processor shut down. In order to avoid waiting for the processor to complete its turn-on cycle again, you can install the ES3 by connecting it in series to the processor power supply cables.

Read More

RCA connector for effortless and fast connections between the head unit PRE OUTs (2 V min.) and bit Ten, bit Ten D Hi-Level inputs.

PACKAGE: Carton Box – Qty. 1

Read More

It is a kit composed of a cable and an adapter allowing a 2 m / 78.74 in. additional extension of the cable supplied with the DRC. This extension is required for installations on especially long vehicles such as SUV’s. Total length of the supplied cable with the extension is equal to 6,5 m / 225.90 in.

PACKAGE: Polybag – Qty. 1

Read More
bit Ten
AUDIO PROCESSOR

bit Ten is a multi-function digital processor featuring analog input, capable of transforming ordinary OEM or after-market system into a high-performance system.
Provided with a 32 bit, 147 MHz clock speed DSP as well as 24 bit A/D and D/A converters, bit Ten is controlled by a software especially developed for signal treatment according to the vehicle acoustic peculiarities.
Setting the parameters of each input single channel, setting the delays according to the listening position, adjusting crossovers and equalizers for each of the 5 output channels; all of these operations can be managed by the PC.
During the installation phase, after converting the analog signal into digital, bit Ten automatically reconstructs a digital full-bandwidth stereo signal; de-equalizes the frequency response and, if necessary, reconstructs the central and subwoofer channels.
The user can configure the output mode of each channel relative to the installed system.
It is designed to be connected with the DRC, Digital Remote Control (optional).

Read More
Docs
Download PC-Software and Firmware
Tech. Features
Analog Inputs 4 high lev. + 2 pre in
Digital Inputs Not available
Analog Outputs 5
Digital Outputs Not available
Equalizers for each Outputs 31-band graphic equalizer (1/3 Oct.; ±12dB)
Crossover Filter Type Full / Hi-Pass / Low Pass / Band Pass
Filter mode and slope Linkwitz @ 12 / 24
Butterworth @ 6 / 12 / 18 / 24
Features
BIT DRIVE

Auto tuning by Audison bit Tune and communication with bit Drive portal.

DE-EQ

De-equalization function to “flatten” any equalization applied by default by OEM sources.

USS technology

USS technology allows bit processors to work with headunits featuring the “speaker load detection” circuit

Press review
Accessories

The new Audison DRC MP (Digital Remote Control Multimedia Play) is compatible with all the Audison electronics featuring AC Link bus. Its slim profile along with the holder supplied with it eases the installation in the best position inside the car. Thanks to the new Joystick, “Rubber Touch” finished for best control of the movements along the four direction axes, the “DRC Settings” menu can be adjusted and navigation is also possible through the “Navi Command” function if the system features an Audison bit Play HD with video output connected to a monitor.

Read More

DRC AB enables the main system control (volume, balance, fader and subwoofer volume, bass-boost) without the use of a PC. Thanks to this device, installed in an ergonomic position within the car dashboard, the user can: choose between the four DSP presets and select the source among master, auxiliary and the two optical digital inputs.

Read More

Stereo passive mixer (unpowered) featuring 4 input channels and 2 output channels, designed for active OEM multi-way systems where each speaker is powered by one specific amplified channel. SPM4 mixes audio through 4 audio transformers specifically developed to achieve very low distortion and highly linear acoustic response. SPM4 provides the ability to mix the midrange/woofer and tweeter channels coming from the amplifier and supply one single mid-high channel. The Ch1(L/R) channels feature two inputs, one features an inverting input compared to Ch2 (L/R) channels; the mixing process often gives better results when one of the two channels undergoes a 180° dephasing. SPM4 is especially recommended to extend the number of inputs of the Audison digital processors or amplifiers with built-in DSP because they feature a De-equalizer (De-Eq). In that case, any possible non-linear acoustic emissions due to the mixing of the pre-existing filtered channels are duly compensated.

Read More

It prevents the processor from shutting down when turning on vehicles featuring the start & stop system

When starting the engine, the vehicle battery voltage might decrease below 8 Volts value. If a signal processor (bit One, bit Ten) is installed in your system, especially with vehicles featuring the start & stop system, low supply voltage values might make the processor shut down. In order to avoid waiting for the processor to complete its turn-on cycle again, you can install the ES3 by connecting it in series to the processor power supply cables.

Read More

RCA connector for effortless and fast connections between the head unit PRE OUTs (2 V min.) and bit Ten, bit Ten D Hi-Level inputs.

PACKAGE: Carton Box – Qty. 1

Read More

It is a kit composed of a cable and an adapter allowing a 2 m / 78.74 in. additional extension of the cable supplied with the DRC. This extension is required for installations on especially long vehicles such as SUV’s. Total length of the supplied cable with the extension is equal to 6,5 m / 225.90 in.

PACKAGE: Polybag – Qty. 1

Read More
Register your product now to add 1 additional year of warranty coverage.
Register